If a dice is rolled ‘out of bounds’ (i.e. Wherever you roll your dice, make sure you roll the dice where your opponent can see the results too. Many gamers roll their dice somewhere on the battlefield, but some roll their dice elsewhere, such as in a dice tray. It is good practice to always make sure your opponent knows what you are rolling dice for, and what abilities and rules are in effect that enable you to make any re-rolls. Hints and Tips – Dice Rolling In a game of Warhammer 40,000 you and your opponent will be rolling, and in some cases re-rolling, lots of dice. Rules that refer to the value of an ‘unmodified’ dice roll are referring to the dice result after any re-rolls, but before any modifiers are applied. You can never re-roll a dice more than once, and re-rolls happen before modifiers (if any) are applied.
For example, if a rule states to re-roll results of 1, and you roll a D3, you would re-roll if the D6 rolled a 1 or a 2 (which is then halved to get a D3 value of a 1). If a rule allows you to re-roll a specific dice result, but the result is obtained by halving a D6 (such as when rolling a D3), you use the value of the halved roll to determine if it can be re-rolled, not the value of the original D6. If a rule allows you to re-roll specific dice results, only those dice can be re-rolled. If a rule allows you to re-roll a dice roll that was made by adding several dice together (2D6, 3D6 etc.) then, unless otherwise stated, you must re-roll all of those dice again. Re-rollsSome rules allow you to re-roll a dice roll, which means you get to roll some or all of the dice again. If a rule says it affects units that are ‘wholly within’ then it only applies if every part of every model’s base (or hull) in that unit is within the specified distance. If a rule says it affects units if ‘every model in that unit is within’ then that rule applies so long as any part of every model’s base (or hull) is within the specified distance. If a rule says it affects units that are ‘within’, then it applies so long as any part of any model’s base (or hull) in that unit is within the specified distance. If a rule says it affects models that are ‘wholly within’ then it only applies if every part of the model’s base (or hull) is within the specified distance. If a rule says it affects models that are ‘within’, then it applies so long as any part of the model’s base (or hull) is within the specified distance. For example, within 1" means any distance that is not more than 1" away. Within and Wholly WithinIf a rule says it applies ‘within’ a certain distance, it applies at any distance that is not more than the specified distance. When this is the case, any models that cannot be set up are considered to have been destroyed. Sometimes there will be insufficient room to set up all the models from a unit, or it will not be possible to set up all the models so that they are in unit coherency.
Some rules allow you to add models to a unit during the battle such models must always be set up in unit coherency with the unit they are being added to. Units are primarily moved in the Movement phase, but they can also be moved in the Charge phase and the Fight phase. If a unit cannot end any kind of move in unit coherency, that move cannot be made. While a unit has six or more models, all models must instead be within 2" horizontally and 5" vertically of at least two other models from their unit. Unit CoherencyA unit that has more than one model must be set up and finish any sort of move as a single group, with all models within 2" horizontally and 5" vertically of at least one other model from their unit. If another rule uses keywords in angular brackets, then that keyword matches the keyword that you selected of the unit using that rule. You must decide what these keywords will be at the moment such a unit is added to your army (whether before the battle or during). This is shorthand for keywords that you can select yourself (with certain restrictions, as described in the publication that contains that datasheet).
Some datasheets have keywords that are presented in angular brackets, such as, and. The pluralisation (or not) of keywords does not affect which units the rule in question applies to. This means it only applies to units that have the INFANTRY keyword on their datasheet. For example, a rule might say that it applies to ‘ INFANTRY units’. Keywords are sometimes linked to (or ‘tagged’ by) a rule.
In either case, keywords appear in KEYWORD BOLD in the rules. The former can be used as a guide to help decide which models to include in your army, but otherwise both sets of keywords are functionally the same. 40k crusade pdf.KeywordsAll datasheets have a list of keywords, separated into Faction keywords and other keywords.
0 kommentar(er)
